Keysight (Agilent) 34420A REPAIR and Keysight (Agilent) 34420A CALIBRATION

 
Custom-Cal has a high success rate in the repair of the Keysight (Agilent) 34420A. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the Keysight (Agilent) 34420A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Multimeter DMM?
Shop for Comparable Products on our
 used Multimeter DMM page

 
   Keysight (Agilent) 34420A   Description / Specification:    
Keysight (Agilent) 34420A Nanovolt/Micro-ohm Meter

The HP 34420A Nanovolt/Micro-ohm Meter has two input channels that allows voltage measurements to be made independently, or they can be mathematically combined to make difference and ratio measurements. Ohms measurements combine the low-noise input circuit s with a highly stable current source to provide outstanding low-resistance measurements. Offset compensation is employed to eliminate the effects of stray thermal EMFs that would otherwise result in measurement error. Low power ohms and a new low-voltage resistance measurement capability allow repeatable measurements to be made where a low voltage (20 mV) is required to avoid oxidation punch-thru. A wide range of temperature measurement capabilities are also built in, providing support for thermocouple, RTD, and thermistor temperature sensors. A shielded copper pin screw-down connector, a 7 1/2-digit A/D converter, 2 ppm basic dc accuracy, and a new measurement algorithm that gives 100 dB normal mode rejection without front-end filtering result in measurement capability you can depend on to make accurate and repeatable low-level measurements. Specifications. DC Voltage - 7 1/2 digits resolution all ranges, Ranges: 1 mV to 100V. Resistance - 7 1/2 digits resolution all ranges, Ranges: 1 ohm to 1 M-ohm. Low Power Resistance Ranges: 1 ohm to 100 k-ohm. Voltage Limited Resistance (Voltage limit selectable: 20 mV, 100 mV, or 500 mV): 10 ohm and 100 ohm. Test Current/Maximum Lead Resistance Ranges: 1 ohm to 1 M-ohm. Resistance: 2 or 4-wire ohm; offset compensation used on all ranges except 100 k-ohm and 1 M-ohm range; can be turned off. Temperature Thermocouple: Type B, E, J, K, N, R, S, T; Thermistor: 5 k-ohm. Interface: IEEE-488 and RS-232 standard.



 

Standard Calibration $245.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the Keysight (Agilent) 34420A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc
dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Load Regulation
Load regulation is the capability to maintain a constant voltage (or current) level on the output channel of a power supply despite changes in the supply's load (such as a change in resistance value connected across the supply output).

Power Linearity
When changing the power level and measuring the differences (in dB) between actual and displayed power levels, the power linearity is ± half the span (in dB) between the maximum and the minimum value of all differences.

Settling Time
Settling time of an output device is the time elapsed from the application of an ideal instantaneous step input to the time at which the amplifier output has entered and remained within a specified error band, usually symmetrical about the final value.


Please contact us for your Keysight (Agilent) 34420A REPAIR and/or Keysight (Agilent) 34420A Nanovolt/Micro-ohm Meter CALIBRATION

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: