AEROFLEX-IFR FM/AM-500A CALIBRATION and AEROFLEX-IFR FM/AM-500A REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the AEROFLEX-IFR FM/AM-500A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Communication Analyzer?
Shop for Comparable Products on our
 used Communication Analyzer page or new Communication Analyzer page

 
   AEROFLEX-IFR FM/AM-500A (500A)   Description / Specification:    
AEROFLEX-IFR FM/AM-500A Communications Service Monitor

The IFR-Aeroflex FM/AM-500A Communications Service Monitor is the perfect test solution for a wide range of wireless communication test requirements. Typical applications include FM/AM testing, conventional two-way radio test, SSB testing and basic communication systems performance tests. Standard Features. FM and AM Signal Generator. 2 uV receiver for AM, FM and SSB. 10 Hz to 9999.9 Hz variable audio generator and audio frequency error meter. 1 kHz audio generator. Frequency error meter with 1 Hz resolution. Peak/Average watt meter. Deviation measurement to 60 kHz. SINAD/ Distortion Meter. 0.2 ppm TCXO. Microphone input. Audio demodulator output. Specifications. RF Signal Generator Frequency Range: 250 kHz to 999.9999 MHz. Resolution: 100 Hz. Variable Generate: Continuous tuning ± 10 kHz from selected frequency. Residual FM: < 100 Hz peak RMS. RF Output Power: -127 dBm to -20 dBm (10 dB steps with 11 dB range continuous vernier). RF Output Accuracy: ± 3 dB. Audio Generator Operating Modes: Internal, Speaker, External + Internal. Tone Output Level: 0 to 2.5 VRMS into 150 ohm load. Frequency Range: 10 Hz to 9999.9 Hz in 0.1 Hz increments. Generate Amplifier Gain: 30 dB ± 2 dB typical, 100 kHz to 1000 MHz. Power Meter Range: 0 to 15 and 0 to 150 W peak or average responding. Receiver Monitor Frequency Range: 100 kHz to 999.9999 MHz in 100 Hz increments. Sensitivity: 2 uV (1 MHz to 1000 MHz, FM Narrow).



 

Standard Calibration $590.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the AEROFLEX-IFR FM/AM-500A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Communication Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Data Rate
Data Rate is the maximum number of bits of information which can be transmitted per second, as in a data transmission link. Typically expressed as megabits per second (Mbps).

Optical Signal-to-noise Ratio (OSNR)
Optical Signal-to-noise ratio is the ratio between the signal power and the noise power in a given bandwidth. Most commonly a reference bandwidth of 0.1 nm is used. This bandwidth is independent from the modulation format, the frequency and the receiver. For instance a OSNR of 20dB/0.1nm could be given, even the signal of 40 GBit DPSK would not fit in this bandwidth. OSNR is measured with a Optical Spectrum Analyzer. It is generally measured at the wavelength of interest.

SONET
Synchronous Optical NETwork (SONET) is a fiber-optic transmission system for high-speed digital traffic. Employed by telephone companies and common carriers, speeds range from 51 Mbps to 40 Gbps. SONET is an intelligent system that provides advanced network management and a standard optical interface. Specified in the Broadband ISDN (B-ISDN) standard, SONET backbones are widely used to aggregate T1 and T3 lines. The European counterpart to SONET is the Synchronous Digital Hierarchy, and the term "SONET/SDH" is widely used when referring to SONET


Please contact us for your AEROFLEX-IFR FM/AM-500A CALIBRATION and/or AEROFLEX-IFR FM/AM-500A Communications Service Monitor REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: