A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the NOISE-COM UFX7110 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.


   NOISE-COM UFX7110   Description / Specification:    
NOISE-COM UFX7110 1.5 GHz Amplified Noise Source

The Noise Com UFX7110 is a 1.5 GHz amplified noise source that is tuned to provide the best flatness at the instrument output. The amplifier is optimized to deliver an output with a Gaussian amplitude distribution. Noise output power level can be adjusted from 0 to 127 dB in 1 dB (optionally 0.1 dB) steps.


Frequency Range: 100 Hz - 1.5 GHz.
Power: + 10 dBm.
dBm/Hz: -82.
Flatness: ±1.5 dBm.
μV/sqrt(Hz): 18.2.
Output: White Gaussian noise.
Attenuator: 0 to 127 dB in 1 dB steps, 0 to 79 dB above 2 GHz, (0.1 dB steps optional).
Control: Local and IEEE-488.
Impedance: 50 ohms (others optional).
Typical VSWR: 1.5:1.
Standard output connector: SMA female.

U7opt01: N female output connector.
U7opt02: BNC female output connector.
U7opt03: 0 to 127.9 dB noise attenuator in 0.1 dB steps instead of 127 dB in 1 dB steps.
U7opt04: Switch elements, 2 X SP6T for 4 subband filters, 1 thrupath, 1 termination (filters are optional).
U7opt06: 75 ohm output impedance (6 dB loss in the noise path and 12 dB loss in the signal path).
U7opt07: Combiner for input signal (6 dB loss in noise and signal paths).
U7opt08: Double output terminals (switched).
U7opt10: Line power 230 VAC, 50 Hz.
U7opt11: RS-232C, RS-422, RS-423, in addition to standard IEEE-488 interface.
U7opt12: 0 to 127 dB signal attenuator in 1 dB steps.
U7opt13: 0 to 127.9 dB signal attenuator in 0.1 dB steps.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Channel Bandwidth
Channel Bandwidth is the bandwidth over which power is measured. This is usually the bandwidth in which almost all of the power of a signal is contained.

Jitter in technical terms is the deviation in or displacement of some aspect of the pulses in a high-frequency digital signal. Jitter is the time variation of a periodic signal in electronics and telecommunications, often in relation to a reference clock source. Jitter may be observed in characteristics such as the frequency of successive pulses, the signal amplitude, or phase of periodic signals. Jitter is a significant, and usually undesired, factor in the design of almost all communications links (e.g., USB, PCI-e, SATA, OC-48). In clock recovery applications it is called timing jitter.

Overshoot is the distortion that follows a major transition; the difference between the peak power point and the pulse-top amplitude computed as a percentage of the pulse-top amplitude.

Rise Time
Rise time refers to the time required for a signal to change from a specified low value to a specified high value, usually 10 and 90 percent of pulse-top amplitude (vertical display is linear power).

Please contact us for your NOISE-COM UFX7110 CALIBRATION and/or NOISE-COM UFX7110 1.5 GHz Amplified Noise Source REPAIR

I'm interested in: 
Calibration Type (Select one):

Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:

What is the description of the problem?

How/when did the problem start?

 (*) Required Fields    For formal quote please fill in all fields.
From (Email):*
Contact Name:*
Address 1:
Address 2:
State/Territory/Province: *
Zip/Postal Code: