NOISE-COM UFX7107 CALIBRATION and NOISE-COM UFX7107 REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the NOISE-COM UFX7107 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

 

 
   NOISE-COM UFX7107   Description / Specification:    
NOISE-COM UFX7107 100 MHz Amplified Noise Source

The Noise Com UFX7107 is a 100 MHz amplified noise source that is tuned to provide the best flatness at the instrument output. The amplifier is optimized to deliver an output with a Gaussian amplitude distribution. Noise output power level can be adjusted from 0 to 127 dB in 1 dB (optionally 0.1 dB) steps.

Specifications.

Frequency Range: 100 Hz - 100 MHz.
Power: + 13 dBm.
dBm/Hz: -67.
Flatness: ±0.75 dBm.
μV/sqrt(Hz): 100.
Output: White Gaussian noise.
Attenuator: 0 to 127 dB in 1 dB steps, 0 to 79 dB above 2 GHz, (0.1 dB steps optional).
Control: Local and IEEE-488.
Impedance: 50 ohms (others optional).
Typical VSWR: 1.5:1.
Standard output connector: SMA female.

Options.
U7opt01: N female output connector.
U7opt02: BNC female output connector.
U7opt03: 0 to 127.9 dB noise attenuator in 0.1 dB steps instead of 127 dB in 1 dB steps.
U7opt04: Switch elements, 2 X SP6T for 4 subband filters, 1 thrupath, 1 termination (filters are optional).
U7opt06: 75 ohm output impedance (6 dB loss in the noise path and 12 dB loss in the signal path).
U7opt07: Combiner for input signal (6 dB loss in noise and signal paths).
U7opt08: Double output terminals (switched).
U7opt10: Line power 230 VAC, 50 Hz.
U7opt11: RS-232C, RS-422, RS-423, in addition to standard IEEE-488 interface.
U7opt12: 0 to 127 dB signal attenuator in 1 dB steps.
U7opt13: 0 to 127.9 dB signal attenuator in 0.1 dB steps.



 



Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc
dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Load Regulation
Load regulation is the capability to maintain a constant voltage (or current) level on the output channel of a power supply despite changes in the supply's load (such as a change in resistance value connected across the supply output).

Power Linearity
When changing the power level and measuring the differences (in dB) between actual and displayed power levels, the power linearity is ± half the span (in dB) between the maximum and the minimum value of all differences.

Settling Time
Settling time of an output device is the time elapsed from the application of an ideal instantaneous step input to the time at which the amplifier output has entered and remained within a specified error band, usually symmetrical about the final value.


Please contact us for your NOISE-COM UFX7107 CALIBRATION and/or NOISE-COM UFX7107 100 MHz Amplified Noise Source REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: