BERKELEY NUCLEONICS CORPORATION 505-2C CALIBRATION and BERKELEY NUCLEONICS CORPORATION 505-2C REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the BERKELEY NUCLEONICS CORPORATION 505-2C Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Pulse Generator?
Shop for Comparable Products on our
 used Pulse Generator page or new Pulse Generator page

 
For Sale New, List Price $2,175.00   BERKELEY NUCLEONICS CORPORATION 505-2C   Description / Specification:   Spec Sheet 
BERKELEY NUCLEONICS CORPORATION 505-2C Two Channel Pulse Generator

The BNC 505-2C Two Channel Pulse Generator has multiple modes of operation and 16 different edges in a single instrument. As a pulse generator it provides rate, delay, width, and output adjustability with each channel. As a digital delay generator, model 505 provides fine resolution, timing, and low jitter.
The outputs are synchronized to one another with coherence of 5 ns. A channel’s timing can be referenced to any other channel or to the zero delay point (To) The edges are adjustable in 100 ns steps. Channels can be selectively gated, enabled / disabled. Each channel possesses separate output level and polarity characteristics along with system level gating capability. Model 505 provides the ability to store custom parameter settings which are able to be recalled for later use.
Specifications.

Electrical Outputs: 2.

TIMING DELAYS AND WIDTHS.
Delay: 0 to 1000 seconds with 100 ns resolution.
Width: 100 ns to 1000 seconds with 10 ns resolution.
Accuracy: 10 ns + .0001 delay.
Time base: 50 MHz, 50 ppm crystal oscillator.
RMS jitter: < 2 ns.

EXTERNAL TRIGGER/GATE.
Rate: 0 to 2 MHz.
Insertion delay: < 250 ns.
Threshold: 200 mV - 15V.
Trigger slope: Rising or falling edge, selectable.
Gate: Active low or active high, selectable.
Impedance: 1000 ohms.

INTERNAL REP RATE GENERATOR.
Rate: 0.001 Hz to 2 MHz.
Accuracy: 5 ns + 0.0001 x period.
RMS jitter: < 500 ps.
OUTPUTS: Adjustable to 20 V.
IMPEDANCE: 50 ohm.

ADJUSTABLE AMPLITUDE.
Slew rate: > 0.2 V/ns.
Amplitude: 1V - 10V into 50 ohm load, 2 V - 20 V into high impedance.
Peak current: 150 mA per channel.
Average current: 200 mA average (total for all channels).
Polarity: Positive (active high) or Negative (low).

COMPUTER INTERFACE.
RS232: 4800, 9600, 19200 & 38400.
IEEE 4888: Standard.



 



Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc
dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Load Regulation
Load regulation is the capability to maintain a constant voltage (or current) level on the output channel of a power supply despite changes in the supply's load (such as a change in resistance value connected across the supply output).

Power Linearity
When changing the power level and measuring the differences (in dB) between actual and displayed power levels, the power linearity is ± half the span (in dB) between the maximum and the minimum value of all differences.

Settling Time
Settling time of an output device is the time elapsed from the application of an ideal instantaneous step input to the time at which the amplifier output has entered and remained within a specified error band, usually symmetrical about the final value.


Please contact us for your BERKELEY NUCLEONICS CORPORATION 505-2C CALIBRATION and/or BERKELEY NUCLEONICS CORPORATION 505-2C Two Channel Pulse Generator REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: