AWT GLOBAL T5230A CALIBRATION and AWT GLOBAL T5230A REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the AWT GLOBAL T5230A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Network Analyzer, SNA, VNA?
Shop for Comparable Products on our
 used Network Analyzer, SNA, VNA page or new Network Analyzer, SNA, VNA page

 
   AWT GLOBAL T5230A   Description / Specification:    
AWT GLOBAL T5230A 3.0 GHz, 2 port Vector Network Analyzer

The AWT-Global T5230A is a high performance VNA that has large dynamic range, low noise level and low trace noise. Its frequencies cover all bands of wireless communication. This VNA is widely used in microwave device measurement in wireless communication, broadcast, television devices, radar devices, semi conductors and many more.

Specifications.

Measurement Range.
Impedance: 50 Ω, 75 Ω (with adapter).
Test port connector: N-type (f).
Number of test ports: 2.
Frequency range: 300 kHz to 3.0 GHz.
Full CW frequency accuracy: +/- 5 x 10-6
Frequency resolution: 1 Hz.
Measurement points: 2 to 10001.
Measurement bandwidths: 1 Hz to 30 kHz (in 1/ 1.5/ 2/ 3/ 5/ 7 steps).
Dynamic range: 130 dB/135 dB typ. (IFBW=10Hz).

Measurement Accuracy.
Accuracy of transmission measurements (magnitude/phase):
  +5 to +15dB, 0.2 dB / 2°;
  -50 to +5 dB, 0.1 dB / 1°;
  -70 to - 50 dB, 0.2 dB / 2°;
  -90 to - 70 dB, 1.0 dB / 6°.
Accuracy of reflection measurements (magnitude/phase):
  -15 to 0 dB, 0.4 dB / 3°;
  -25 to -15 dB, 1.5 dB / 7°;
  -35 to -25 dB, 4.0 dB / 22°.
Trace noise magnitude: 1 mdB rms (IFBW = 3 kHz).
Temperature dependence: 0.02 dB.

Test Port Output.
Match (w/o system error correction): 18 dB.
Power range 300 kHz to 3.0 GHz: -55 dBm to +10 dBm.
Power accuracy: +/- 1.5 dB.
Power resolution: 0.05 dB.
Harmonics distortion: < -25 dBc.
Non harmonics distortion: < -30 dBc.

Test Port Input.
Match (w/o system error correction): 18 dB.
Damage level: +26 dBm.
Maximum DC voltage: +35 V.
Noise level: < -120 dBm (IFBW = 10 Hz).

Measurement Speed.
Measurement time per point: 125 ms.
Source to receiver port switch overtime: <10 ms.



 



Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Average Power
Average power means that the energy transfer rate is to be averaged over many periods of the lowest frequency involved. For a CW signal, the lowest frequency and highest frequency are the same, so average power and power are the same. For an amplitude modulated wave, the power must be averaged over many periods of the modulation component of the signal as well.

Harmonic
A harmonic of a wave is a component frequency of the signal that is an integer multiple of the fundamental frequency, i.e. if the fundamental frequency is f, the harmonics have frequencies 2f, 3f, 4f, . . . etc.

Phase Noise
Phase noise is the frequency domain representation of rapid, short-term, random fluctuations in the phase of a waveform, caused by time domain instabilities. Phase noise (L(f)) is typically expressed in units of dBc/Hz, representing the noise power relative to the carrier contained in a 1 Hz bandwidth centered at a certain offsets from the carrier.


Please contact us for your AWT GLOBAL T5230A CALIBRATION and/or AWT GLOBAL T5230A 3.0 GHz, 2 port Vector Network Analyzer REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: