AWT GLOBAL T5280A CALIBRATION and AWT GLOBAL T5280A REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the AWT GLOBAL T5280A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Network Analyzer, SNA, VNA?
Shop for Comparable Products on our
 used Network Analyzer, SNA, VNA page or new Network Analyzer, SNA, VNA page

 
   AWT GLOBAL T5280A   Description / Specification:    
AWT GLOBAL T5280A 8.0 GHz, 2 port Vector Network Analyzer

The AWT-Global T5280A is a high performance VNA that has large dynamic range, low noise level and low trace noise. Its frequencies cover all bands of wireless communication. This VNA is widely used in microwave device measurement in wireless communication, broadcast, television devices, radar devices, semi conductors and many more.

Specifications.

Measurement Range.
Impedance: 50 Ω, 75 Ω (with adapter).
Test port connector: N-type (f).
Number of test ports: 2.
Frequency range: 300 kHz to 8.0 GHz.
Full CW frequency accuracy: +/- 5 x 10-6
Frequency resolution: 1 Hz.
Measurement points: 2 to 10001.
Measurement bandwidths: 1 Hz to 30 kHz (in 1/ 1.5/ 2/ 3/ 5/ 7 steps).
Dynamic range: 130 dB/135 dB typ. (IFBW=10Hz).

Measurement Accuracy.
Accuracy of transmission measurements (magnitude/phase):
  +5 to +15dB, 0.2 dB / 2°;
  -50 to +5 dB, 0.1 dB / 1°;
  -70 to - 50 dB, 0.2 dB / 2°;
  -90 to - 70 dB, 1.0 dB / 6°.
Accuracy of reflection measurements (magnitude/phase):
  -15 to 0 dB, 0.4 dB / 3°;
  -25 to -15 dB, 1.5 dB / 7°;
  -35 to -25 dB, 4.0 dB / 22°.
Trace noise magnitude: 1 mdB rms (IFBW = 3 kHz).
Temperature dependence: 0.02 dB.

Test Port Output.
Match (w/o system error correction): 18 dB.
Power range 300 kHz to 6.0 GHz: -55 dBm to +10 dBm (6.0 GHz to 8.0 GHz, -60 dBm to +5 dBm).
Power accuracy: +/- 1.5 dB.
Power resolution: 0.05 dB.
Harmonics distortion: < -25 dBc.
Non harmonics distortion: < -30 dBc.

Test Port Input.
Match (w/o system error correction): 18 dB.
Damage level: +26 dBm.
Maximum DC voltage: +35 V.
Noise level: < -120 dBm (IFBW = 10 Hz).

Measurement Speed.
Measurement time per point: 125 ms.
Source to receiver port switch overtime: <10 ms.



 



Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc
dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Noise Density
Noise Density is the amount of noise within a defined bandwidth, usually normalized to 1 Hz.

Spurious Signals
Spurious signals are undesired signals. They can be considered in two classes. They can be stationary; their frequency and amplitude do not change significantly, or non-stationary, where the frequency and/or amplitude change significantly over short time periods.


Please contact us for your AWT GLOBAL T5280A CALIBRATION and/or AWT GLOBAL T5280A 8.0 GHz, 2 port Vector Network Analyzer REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: