ANDO AQ-4139(155) REPAIR and CALIBRATION

 
Custom-Cal has a high success rate in the repair of the ANDO AQ-4139(155). We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Laser Source (DFB-LD-WDM-BBS)?
Shop for Comparable Products on our
 used Laser Source (DFB-LD-WDM-BBS) page or new Laser Source (DFB-LD-WDM-BBS) page

 
   ANDO AQ-4139(155) (AQ4139(155))   Description / Specification:    
ANDO AQ-4139(155) LD Unit

The Ando AQ-4139(155) LD Plug-in is used with AQ-4137 Stabized Light Source. Specifications. Wavelength: 1550 ±30 nm. Spectral half value width: 10 nm or less. Output waveform: CW light, 270Hz chopped light (standard), 1kHz, 2kHz chopped light (option). Output level: -5 dBm. Output Level Stability against temperature: 0.3dB or less at connector output with 0.0 dB attenuation, using CW light. Output Level Stability against temperature: 1dB or less at output of a 2m-long Ando standard optical fiber, using CW light with 0.0 dB attenuation. Output Level Stability Short-term: 0.05 dB or less at output of a 2m-long Ando standard optical fiber, using CW light with 0.0 dB attenuation. External modulation: 300Hz to 100kHz (square wave), BNC connector. Optical connector: FC-PC (NTT specification): standard. Attenuation level range: Maximum 6dB (referenced to OdB point, in steps of 0.1dB).



 

Standard Calibration $185.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANDO AQ-4139(155). Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a contiguous set of frequencies within which a fiber optic component, link or network will operate.

Extinction Ratio (ER)
Extinction Ratio is the ratio of two optical power levels, of a digital signal generated by an optical source, (example a laser diode), where P1 is the optical power level generated when the light source is "on," and P0 is the power level generated when the light source is "off." The extinction ratio may be expressed as a fraction, in dB, or as a percentage.

Optical Signal-to-noise Ratio (OSNR)
Optical Signal-to-noise ratio is the ratio between the signal power and the noise power in a given bandwidth. Most commonly a reference bandwidth of 0.1 nm is used. This bandwidth is independent from the modulation format, the frequency and the receiver. For instance a OSNR of 20dB/0.1nm could be given, even the signal of 40 GBit DPSK would not fit in this bandwidth. OSNR is measured with a Optical Spectrum Analyzer. It is generally measured at the wavelength of interest.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Wavelength Repeatability
Wavelength Repeatability is the random uncertainty in reproducing a wavelength after detuning and re-setting the wavelength. The wavelength repeatability is ± half the span between the maximum and the minimum value of all actual values of these wavelengths. Example test condition: uninterrupted TLS output power, constant power level, temperature within operating temperature range, coherence control off, short time span. Note: NOTE The long-term wavelength repeatability can be obtained by taken the wavelength repeatability and wavelength stability into account.


I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: