ANDO AQ4320D REPAIR and CALIBRATION

 
Custom-Cal has a high success rate in the repair of the ANDO AQ4320D. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Tunable Laser Source (TLS)?
Shop for Comparable Products on our
 used Tunable Laser Source (TLS) page or new Tunable Laser Source (TLS) page

 
   ANDO AQ4320D (AQ-4320D)   Description / Specification:    
ANDO AQ4320D 1520 to 1620 nm Tunable Laser Source

The Ando AQ4320D Tunable Laser Source Specifications. Wavelength range: 1520 to 1620nm. Wavelength set resolution: 0.001nm. Absolute wavelength accuracy: ±0.1nm. Relative wavelength accuracy: ±0.035nm (typ.). Wavelength stability: ±100MHz/hr (±0.8pm/hr) (typ.). Spectral width (Narrow): 1MHz or less, 200kHz (typ.). Spectral width (Wide): 200MHz or more. Side-Mode Suppression Ratio: 50dB or more. Optical output level (1560 to 1600nm): +6dBm or more. Settable optical output range: 20dB or more (0.1dB steps). Optical output stability: 5 min, ±0.01dB or less; 1 hr, ±0.05dB or less; 8 hr, ±0.3dB or less. Optical output accuracy: ±1dB or less. Optical output reproducibility: ±0.04dB. Optical output level flatness: ±0.1dB. RIN: -145dB/Hz (typ.). Internal modulation (CHOP): Set frequency 0.2 to 300kHz; Set resolution 10Hz, 100Hz, 1kHz, 10kHz, 100kHz. External modulation (CHOP): Set frequency 0.2 to 300kHz. Direct modulation: Modulation frequency 100kHz to 300MHz; Modulation rate 5% or less; Modulation input level 0dBm or less. Wavelength sweep speed: 100nm/sec (Max.). Applicable optical fiber: SMF (10/125µm).



 

Standard Calibration $400.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANDO AQ4320D. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a contiguous set of frequencies within which a fiber optic component, link or network will operate.

Extinction Ratio (ER)
Extinction Ratio is the ratio of two optical power levels, of a digital signal generated by an optical source, (example a laser diode), where P1 is the optical power level generated when the light source is "on," and P0 is the power level generated when the light source is "off." The extinction ratio may be expressed as a fraction, in dB, or as a percentage.

Optical Signal-to-noise Ratio (OSNR)
Optical Signal-to-noise ratio is the ratio between the signal power and the noise power in a given bandwidth. Most commonly a reference bandwidth of 0.1 nm is used. This bandwidth is independent from the modulation format, the frequency and the receiver. For instance a OSNR of 20dB/0.1nm could be given, even the signal of 40 GBit DPSK would not fit in this bandwidth. OSNR is measured with a Optical Spectrum Analyzer. It is generally measured at the wavelength of interest.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Wavelength Repeatability
Wavelength Repeatability is the random uncertainty in reproducing a wavelength after detuning and re-setting the wavelength. The wavelength repeatability is ± half the span between the maximum and the minimum value of all actual values of these wavelengths. Example test condition: uninterrupted TLS output power, constant power level, temperature within operating temperature range, coherence control off, short time span. Note: NOTE The long-term wavelength repeatability can be obtained by taken the wavelength repeatability and wavelength stability into account.


I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: