NOISE-COM UFX7109 CALIBRATION and NOISE-COM UFX7109 REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the NOISE-COM UFX7109 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

 

 
   NOISE-COM UFX7109   Description / Specification:    
NOISE-COM UFX7109 1 GHz Amplified Noise Source

The Noise Com UFX7109 is a 1 GHz amplified noise source that is tuned to provide the best flatness at the instrument output. The amplifier is optimized to deliver an output with a Gaussian amplitude distribution. Noise output power level can be adjusted from 0 to 127 dB in 1 dB (optionally 0.1 dB) steps.

Specifications.

Frequency Range: 100 Hz - 1 GHz.
Power: + 10 dBm.
dBm/Hz: -80.
Flatness: ±1.5 dBm.
μV/sqrt(Hz): 22.4.
Output: White Gaussian noise.
Attenuator: 0 to 127 dB in 1 dB steps, 0 to 79 dB above 2 GHz, (0.1 dB steps optional).
Control: Local and IEEE-488.
Impedance: 50 ohms (others optional).
Typical VSWR: 1.5:1.
Standard output connector: SMA female.

Options.
U7opt01: N female output connector.
U7opt02: BNC female output connector.
U7opt03: 0 to 127.9 dB noise attenuator in 0.1 dB steps instead of 127 dB in 1 dB steps.
U7opt04: Switch elements, 2 X SP6T for 4 subband filters, 1 thrupath, 1 termination (filters are optional).
U7opt06: 75 ohm output impedance (6 dB loss in the noise path and 12 dB loss in the signal path).
U7opt07: Combiner for input signal (6 dB loss in noise and signal paths).
U7opt08: Double output terminals (switched).
U7opt10: Line power 230 VAC, 50 Hz.
U7opt11: RS-232C, RS-422, RS-423, in addition to standard IEEE-488 interface.
U7opt12: 0 to 127 dB signal attenuator in 1 dB steps.
U7opt13: 0 to 127.9 dB signal attenuator in 0.1 dB steps.



 

Standard Calibration $390.00 *
*This is a Web introductory price for one calibration of the NOISE-COM UFX7109. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Average Power
Average power means that the energy transfer rate is to be averaged over many periods of the lowest frequency involved. For a CW signal, the lowest frequency and highest frequency are the same, so average power and power are the same. For an amplitude modulated wave, the power must be averaged over many periods of the modulation component of the signal as well.

Dynamic range
Dynamic range the ratio of a specified maximum level of a parameter, such as power, current, voltage or frequency, to the minimum detectable value of that parameter.

Modulation
Modulation is the process by which the characteristic of one wave (the carrier) is modified by another.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Please contact us for your NOISE-COM UFX7109 CALIBRATION and/or NOISE-COM UFX7109 1 GHz Amplified Noise Source REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: