NOISE-COM UFX7112 CALIBRATION and NOISE-COM UFX7112 REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the NOISE-COM UFX7112 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

 

 
   NOISE-COM UFX7112   Description / Specification:    
NOISE-COM UFX7112 2 GHz Amplified Noise Source

The Noise Com UFX7112 is a 2 GHz amplified noise source that is tuned to provide the best flatness at the instrument output. The amplifier is optimized to deliver an output with a Gaussian amplitude distribution. Noise output power level can be adjusted from 0 to 127 dB in 1 dB (optionally 0.1 dB) steps.

Specifications.

Frequency Range: 1 MHz - 2 GHz.
Power: 0 dBm.
dBm/Hz: -93.
Flatness: ±2.0 dBm.
μV/sqrt(Hz): 5.01.
Output: White Gaussian noise.
Attenuator: 0 to 127 dB in 1 dB steps, 0 to 79 dB above 2 GHz, (0.1 dB steps optional).
Control: Local and IEEE-488.
Impedance: 50 ohms (others optional).
Typical VSWR: 1.5:1.
Standard output connector: SMA female.

Options.
U7opt01: N female output connector.
U7opt02: BNC female output connector.
U7opt03: 0 to 127.9 dB noise attenuator in 0.1 dB steps instead of 127 dB in 1 dB steps.
U7opt04: Switch elements, 2 X SP6T for 4 subband filters, 1 thrupath, 1 termination (filters are optional).
U7opt06: 75 ohm output impedance (6 dB loss in the noise path and 12 dB loss in the signal path).
U7opt07: Combiner for input signal (6 dB loss in noise and signal paths).
U7opt08: Double output terminals (switched).
U7opt10: Line power 230 VAC, 50 Hz.
U7opt11: RS-232C, RS-422, RS-423, in addition to standard IEEE-488 interface.
U7opt12: 0 to 127 dB signal attenuator in 1 dB steps.
U7opt13: 0 to 127.9 dB signal attenuator in 0.1 dB steps.



 

Standard Calibration $475.00 *
*This is a Web introductory price for one calibration of the NOISE-COM UFX7112. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a contiguous set of frequencies within which a component, link or network will operate.

Frequency Span
Frequency Span specifies the range between the start and stop frequencies, also referred to as bandwidth

Noise Figure
Noise Figure the ratio of the signal-to-noise power ratio at the input to the signal-to-noise power ratio at the output.

Ringing
Ringing is an unwanted oscillation of a voltage or current.

Please contact us for your NOISE-COM UFX7112 CALIBRATION and/or NOISE-COM UFX7112 2 GHz Amplified Noise Source REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: