ANRITSU 37225B CALIBRATION and ANRITSU 37225B REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ANRITSU 37225B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Network Analyzer, SNA, VNA?
Shop for Comparable Products on our  used Network Analyzer, SNA, VNA page or new Network Analyzer, SNA, VNA page

 
   ANRITSU 37225B   Description / Specification:    
ANRITSU 37225B 13.5 GHz Vector Network Analyzer

The Anritsu 37225B 13.5 GHz Vector Network Analyzer is a microprocessor controlled Analyzer. It is a single-instrument system that contains a built-in signal source, a test set, and an analyzer subsystem. The 37225B provides up to 1601 measurement data points, a built-in hard-disk drive for storing and recalling front panel setups and measurement and calibration data. It provides an on-screen display of total operational time and date of last system calibrations, and the number of power-off cycles since the last calibration.
Specifications

Frequency Range: 40 MHz to 13.5 GHz.
Max Signal Into Port 2: +20 dBm @ 0.04 GHz, +3 dBm 2 to 13.5 GHz.
Noise Floor: -70 dBm @ 0.04 GHz, -98 dBm @ 2 GHz, -98 dBm @ 13.5 GHz.
Receiver Dynamic Range (defined as the ratio of the maximum signal level at Port 2 for 0.1 dB compression to the noise floor at Port 2): 90 @ 0.04 GHz, 101@ 2 GHz, 101 @ 13.5 GHz.
Port 1 Power: 0 dBm @ 0.04 GHz to 13.5 GHz.
System Dynamic Range (defined as the ratio of the power incident on Port 2 in a through line connection to the noise floor at Port 2 (forward measurements only): 70 @ 0.04 GHz, 98 @ 2 GHz, 98 @ 13.5 GHz.
High Level Noise (typical): <0.03 dB and <0.4° peak-to-peak variation in a 1 kHz IF bandwidth up to 20 GHz, <0.08 dB and <0.5° peak-to-peak variation up to 40 GHz.
Measurement Time vs. Span for 101 Data Points (typical): 40 MHz to 13.5 GHz, 500 ms.
Number of Channels: Four independent measurement channels.
Parameters: S11, S21, S22, S12, or user-defined combinations of a1, a2, b1, and b2. All measurements are made without the need to manually reverse the test device.
Data Points: 1601 maximum.
GPIB Interfaces: 2.

Options
Opt 1, Rack Mounting.
Opt. 1A, Rack Mounting.
Opt 2, High Speed Time (Distance) Domain Measurement Capability.
Opt 4, External SCSI-2 Hard Disk Drive Compatibility. 
Opt 7A/N/NF/S/K, Universal Test Port Configuration, Replaces Universal / K Connector (standard) with: 7A - Universal / GPC-7, 7N - Universal / N, male, 7NF - Universal / N, female, 7S - Universal / 3.5 mm, male.
Opt 10A, High Stability Ovenized Time Base and 1 Hz Resolution.



 

Standard Calibration $800.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANRITSU 37225B. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc
dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Noise Density
Noise Density is the amount of noise within a defined bandwidth, usually normalized to 1 Hz.

Spurious Signals
Spurious signals are undesired signals. They can be considered in two classes. They can be stationary; their frequency and amplitude do not change significantly, or non-stationary, where the frequency and/or amplitude change significantly over short time periods.

Please contact us for your ANRITSU 37225B CALIBRATION and/or ANRITSU 37225B 13.5 GHz Vector Network Analyzer REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: