ANRITSU 68147C CALIBRATION and ANRITSU 68147C REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ANRITSU 68147C Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Signal Generator?
Shop for Comparable Products on our
 used Signal Generator page

 
   ANRITSU 68147C   Description / Specification:   Spec Sheet 
ANRITSU 68147C 20 GHz Synthesized Signal Generator

The Anritsu 68147C 20 GHz Ultra Low Noise Synthesized Signal Generator features 10 MHz to 20 GHz analog, step, and manual sweep capability. The 68147C also provides AM/FM/pulse modulation via external modulating signals. Output levels to +17 dBm and optional 0.1 Hz resolution are available at prices comparable to CW-only sources. To meet requirements that expand over time, economical upgrades are available to any higher performing model. Features, performance, and value combine to make the 68147C the optimum source for your network analysis and swept A.T.E. source applications. Specifications. Frequency range: 10 MHz to 20 GHz (Optional frequency extension down to 0.1 Hz). CW mode Output: Twenty independent, presettable CW frequencies (F0 to F9 and M0 to M9). CW mode Accuracy: Same as internal or external 10 MHz time base. CW mode Internal time base stability: With aging; <2 x 10–8/day (<5 x 10–10/day with Option 16), With temperature; <2 x 10–8/°C over 0°C (<2 x 10–10/°C with Option 16). CW mode Resolution: 1 kHz (0.1 Hz with Option 11). Analog Sweep width: Independently selected from 1 MHz to full range continuous sweep. Analog Sweep Accuracy: The lesser of ±30 MHz or (±2 MHz widths) for sweep speeds of <=50 MHz/ms. Output power: +13 dBm (+11 dBm with attenuator) >= 0.01 to < 20 GHz. Minimum leveled output power range: -20 dBm, (-120 dBm with attenuator). Output power resolution: 0.01 dB (log) or 0.001 mV (linear). Option 1 Rack mounting. Option 2A 110 dB step attenuator. Option 2F 120 dB electronic step attenuator. Option 9 Rear panel RF output. Option 11 0.1 Hz frequency resolution. Option 15A High power output. Option 16 High stability time base. Option 18 mmWave bias output. Option 19 SCPI programmability. Option 21 High spectral purity down converter. Option 22 0.1 Hz to 10 MHz audio frequency.



 

Standard Calibration $690.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANRITSU 68147C. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBm
dBm (sometimes dBmW) is an abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). Zero dBm equals one milliwatt. A 3 dB increase represents roughly doubling the power, a 3 dB decrease, the power is reduced by about one half.

Millimeter-wave
Millimeter-wave is a term that generally refers to frequencies of 26.5 GHz and above. That is where signal wavelengths fall below approximately 10 mm, and thus the terminology changes from centimeters to millimeters.

Power Repeatability
Power Repeatability is the random uncertainty in reproducing the power level after changing and re-setting the power level. The power repeatability is ± half the span (in dB) between the highest and lowest actual power. Note: - The long-term power repeatability can be obtained by taken the power repeatability and power stability into account.

Stability
Stability is the extent to which a specified property, characteristic, or parameter of a substance, device, or apparatus, remains fixed with the passage of time or with varying environmental conditions.


Please contact us for your ANRITSU 68147C CALIBRATION and/or ANRITSU 68147C 20 GHz Synthesized Signal Generator REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: