ANRITSU MG3696B CALIBRATION and ANRITSU MG3696B REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ANRITSU MG3696B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Signal Generator?
Shop for Comparable Products on our
 used Signal Generator page

 
   ANRITSU MG3696B   Description / Specification:    
ANRITSU MG3696B 67 GHz Synthesized Signal Generator

The Anritsu MG3696B 67 GHz Synthesized Signal Generator is microprocessor-based, synthesized signal source with high resolution phase-lock capability. It offers unsurpassed frequency coverage, leveled output power, spectral purity, switching speed, modulation performance, size, upgradeability, reliability, and service. The signal generator is configurable for a broad range of applications from R&D to manufacturing and depot repair. It generates both discrete CW frequencies and broad (full range) and narrow band step sweeps across the frequency range of 2 GHz to 67 GHz. Options are available to extend the low end of the frequency range to 0.1 Hz. All functions of the signal generator are fully controllable locally from the front panel or remotely (except for power on/standby) via the IEEE-488 General Purpose Interface Bus (GPIB). Specifications. Frequency Range: 2 to 67 GHz. Output Power (standard): <=20 GHz (+10.0 dBm), >20 to <= 67 GHz (+3.0 dBm). CW Mode Output: Twenty independent, presettable CW frequencies (F0 – F9 and M0 –M9). Accuracy: Same as internal or external 10 MHz time base. Resolution: 0.01 Hz. Phase-Locked Step Sweep Mode nWidth: Independently selected, 0.01 Hz to full range. Every frequency step in sweep range is phase-locked. Accuracy: Same as internal or external 10 MHz time base. Resolution (Minimum Step Size): 0.01 Hz. Markers: Up to 20 independent, settable markers (F0 – F9 and M0 – M9). Options. 2X - Mechanical Step Attenuator. 2E - Electronic Step Attenuator. 3 - Ultra Low Phase Noise, main band. 4 - 10 MHz to 2.2 GHz RF coverage, Ultra-Low Phase Noise version. 5 - 10 MHz to 2 GHz RF coverage. 6 - Analog Sweep Capability. 7 - IF Up-Conversion. 8 - Power Monitor. 9X - Rear Panel Output. 10 - User-Defined Modulation Waveform Software. 12 - Frequency and Phase Modulation. 14 - Amplitude Modulation. 15X - High Power. 16 - High Stability Time Base. 17 - Delete Front Panel. 18 - mmW Bias Output. 20 - Scan Modulation. 22 - 0.1 Hz to 10 MHz Audio coverage. 26X - Pulse Modulation. 27 - Internal LF and Pulse Generators. 28X - Analog Modulation Suite. 30 - Low Phase Noise. 37A - Performance Suite. 38A - Ultra Performance Suite. 39A,B,C,D - CW Power Meter and Sensor Bundle. 40 - Pulse Power Meter and Sensor Bundle.



 

Standard Calibration $835.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANRITSU MG3696B. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBm
dBm (sometimes dBmW) is an abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). Zero dBm equals one milliwatt. A 3 dB increase represents roughly doubling the power, a 3 dB decrease, the power is reduced by about one half.

Millimeter-wave
Millimeter-wave is a term that generally refers to frequencies of 26.5 GHz and above. That is where signal wavelengths fall below approximately 10 mm, and thus the terminology changes from centimeters to millimeters.

Power Repeatability
Power Repeatability is the random uncertainty in reproducing the power level after changing and re-setting the power level. The power repeatability is ± half the span (in dB) between the highest and lowest actual power. Note: - The long-term power repeatability can be obtained by taken the power repeatability and power stability into account.

Stability
Stability is the extent to which a specified property, characteristic, or parameter of a substance, device, or apparatus, remains fixed with the passage of time or with varying environmental conditions.


Please contact us for your ANRITSU MG3696B CALIBRATION and/or ANRITSU MG3696B 67 GHz Synthesized Signal Generator REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: