ILX LIGHTWAVE LDC-3714B CALIBRATION and ILX LIGHTWAVE LDC-3714B REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ILX LIGHTWAVE LDC-3714B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Laser Diode Controller?
Shop for Comparable Products on our
 used Laser Diode Controller page

 
   ILX LIGHTWAVE LDC-3714B   Description / Specification:    
ILX LIGHTWAVE LDC-3714B Laser Diode Controller with Temperature Controller

ILX Lightwave LDC-3714B laser diode current source with integrated 32W temperature controller. Drive Current Output; Range: 0-50mA, 0-100mA. Setpoint Resolution: 1µA (50mA), 2µA (100mA). Setpoint Accuracy: ±0.05% of FS. Compliance Voltage: 0-10V adjustable. Temperature Coefficient: <50ppm/°C. Short-Term Stability (one-hour): <20ppm. Long-Term Stability (24-hour): <40ppm. Noise and Ripple (rms) High Bandwidth Mode: <1.5µA. Noise and Ripple (rms) Low Bandwidth Mode: <1.5µA. Compliance Voltage Adjust; Range: 0-10V. Resolution: 50mV. Accuracy: ±2.5%. Drive Current Limit Settings; Range: 1-50.5mA, 1–101mA. Resolution: 0.25mA(50.5mA), 0.5mA(101mA). Accuracy: ±0.5mA(50.5mA), ±1mA(101mA). Photodiode Feedback; Type: Differential. Photodiode Reverse Bias: 0-5V adjustable. Photodiode Current Range: 5 to 5000µA. Output Stability: 0.02%. Setpoint Accuracy: ±0.05% of FS. External Analog Modulation; Input: 0-10V, 10kohm. Transfer Function: 5mA/V(50.5mA), 10mA/V(101mA). High Bandwidth (3dB): DC to 1MHz. Low Bandwidth (3dB): DC to 15kHz. Trigger Ouput; Type: TTL. Pulse Width: 13µs. Delay: 12ms. Temperature Control; Temperature Control Range: -100°C to 199°C. Thermistor Setpoint: -100°C to 199°C. Resolution: 0.1°C(-20°C to 20°C), 0.2°C(20°C to 50°C). Accuracy: ±0.2°C(-20°C to 50°C). Short-Term Stability (one-hour): ±0.004°C or better. TEC Output; Output Type: Bipolar, constant current source. Compliance Voltage: >8V DC. Maximum Output Current: 4.0A. Maximum Output Power: 32W. Current Noise and Ripple: <1mA rms. Display Type: 5-Digit, Green LED



 

Standard Calibration $240.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ILX LIGHTWAVE LDC-3714B. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a contiguous set of frequencies within which a fiber optic component, link or network will operate.

Extinction Ratio (ER)
Extinction Ratio is the ratio of two optical power levels, of a digital signal generated by an optical source, (example a laser diode), where P1 is the optical power level generated when the light source is "on," and P0 is the power level generated when the light source is "off." The extinction ratio may be expressed as a fraction, in dB, or as a percentage.

Optical Signal-to-noise Ratio (OSNR)
Optical Signal-to-noise ratio is the ratio between the signal power and the noise power in a given bandwidth. Most commonly a reference bandwidth of 0.1 nm is used. This bandwidth is independent from the modulation format, the frequency and the receiver. For instance a OSNR of 20dB/0.1nm could be given, even the signal of 40 GBit DPSK would not fit in this bandwidth. OSNR is measured with a Optical Spectrum Analyzer. It is generally measured at the wavelength of interest.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Wavelength Repeatability
Wavelength Repeatability is the random uncertainty in reproducing a wavelength after detuning and re-setting the wavelength. The wavelength repeatability is ± half the span between the maximum and the minimum value of all actual values of these wavelengths. Example test condition: uninterrupted TLS output power, constant power level, temperature within operating temperature range, coherence control off, short time span. Note: NOTE The long-term wavelength repeatability can be obtained by taken the wavelength repeatability and wavelength stability into account.


Please contact us for your ILX LIGHTWAVE LDC-3714B CALIBRATION and/or ILX LIGHTWAVE LDC-3714B Laser Diode Controller with Temperature Controller REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: