ANRITSU 69097A CALIBRATION and ANRITSU 69097A REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ANRITSU 69097A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Signal Generator?
Shop for Comparable Products on our  used Signal Generator page

 
   ANRITSU 69097A   Description / Specification:    
ANRITSU 69097A 65 GHz Ultra Low Noise Synthesized CW Generator

The Anritsu 69097A 65 GHz Ultra Low Noise Synthesized CW Generator features 10 MHz to 20 GHz analog, step, and manual sweep capability. Output levels to +12 dBm and optional 0.1 Hz resolution. It provides AM and FM via external modulating signals or internal arbitrary waveform generators. The internal generators offer 7 modulating waveforms, including Gaussian noise, as well as user-defined arbitrary waveforms. Pulse modulation parameters can be set externally or by the internal pulse generator. Doublet, triplet, or quadruplet pulses make RADAR blind spot testing easy. Simultaneous synchronized modulations let you set complex signal scenarios across the entire frequency range. Specifications. Frequency Range: 0.01 to 65 GHz. CW mode Output: Twenty independent, presettable CW frequencies (FO to F9 and MO to M9). CW mode Accuracy: Same as internal or external 10 MHz time base. CW mode Resolution: 1 kHz (0.1 Hz with Option 11). Phase-locked step sweep mode Sweep width: Independently selected, 1 kHz (0.1 Hz with Option 11) to full range, every frequency step in sweep range is phase-locked. Phase-locked step sweep mode Resolution (Min. step size): 1 kHz (0.1 Hz with Option 11). Spurious signals Harmonic and harmonic related: <-30 dBc (10 to 50 MHz), <-40 dBc ( >50 MHz to <= 2 GHz), <-60 dBc ( >2 GHz to <= 20 GHz). Output power: +12 dBm (>= 0.01 to <2 GHz), +10 dBm (>= 2 to <=20 GHz), +2.5 dBm (>20 to <=40 GHz), +0 dBm (>40 to <=50 GHz), -2 dBm (>50 to <=65 GHz). Options. Option 2A, Step attenuator. Option 9, Rear panel RF output. Option 11, 0.1 Hz frequency resolution. Option 15, High power output. Option 16, High stability time base. Option 17, Delete front panel. Option 18, MM-wave bias. Option 19, SCPI programmability adds GPIB command mnemonics.



 

Standard Calibration $1,135.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANRITSU 69097A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBm
dBm (sometimes dBmW) is an abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). Zero dBm equals one milliwatt. A 3 dB increase represents roughly doubling the power, a 3 dB decrease, the power is reduced by about one half.

Millimeter-wave
Millimeter-wave is a term that generally refers to frequencies of 26.5 GHz and above. That is where signal wavelengths fall below approximately 10 mm, and thus the terminology changes from centimeters to millimeters.

Power Repeatability
Power Repeatability is the random uncertainty in reproducing the power level after changing and re-setting the power level. The power repeatability is ± half the span (in dB) between the highest and lowest actual power. Note: - The long-term power repeatability can be obtained by taken the power repeatability and power stability into account.

Stability
Stability is the extent to which a specified property, characteristic, or parameter of a substance, device, or apparatus, remains fixed with the passage of time or with varying environmental conditions.

Please contact us for your ANRITSU 69097A CALIBRATION and/or ANRITSU 69097A 65 GHz Ultra Low Noise Synthesized CW Generator REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: