NOYES OFL250-100 CALIBRATION and NOYES OFL250-100 REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the NOYES OFL250-100 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another OTDR? Shop for Comparable Products on our   new OTDR page

 
   NOYES OFL250-100   Description / Specification:    
NOYES OFL250-100 Handheld OTDR, OPM, LS and VFL

The NOYES OFL250-100 1310/1550 nm single-mode OTDR and Laser Source, Optical Power Meter and Visual Fault Locator. Ideal for installation and maintenance testing of access and metro area networks operating at 1310 and/or 1550 nm. With short dead zone and 26 dB dynamic range performance, the OFL250-100 is ideal for troubleshooting single-mode fibers in local access and metro area networks. The OFL250-100 provides automatic and manual setup, automatic event detection, 12-hour battery life, internal data storage and USB connectivity. OTDR/OLS, OPM and VFL test ports are equipped with tool-free adapters, which can be changed in seconds. OTDR Specifications. Emitter Type: Laser. Available Wavelengths: 1310/1550 nm. Wavelength Tolerance: ±20/±20 nm. Dynamic Range (SNR = 1): 26 dB. Event Dead Zone: 1.5 m. Attenuation Dead Zone: 6.5/7 m. Pulse Widths: 5, 10, 30, 100, 300 ns, 1, 3, 10 ?s. Range Settings: 250 m to 256 km. Data Point Spacing: 12.5 cm (range <4 km), Range/16,000 (range >4 km). Group Index of Refraction (GIR): 1.4000 to 1.6000. Distance Uncertainty: ±(1 + 0.005 % x distance + data point spacing). OPM Specifications. Calibrated Wavelengths: 1310, 1490, 1550, 1625, 1650 nm. Detector Type: InGaAs. Measurement Range: +23 to -50 dBm. Accuracy @ -10 dBm: ±0.25 dB. Resolution: 0.01 dB. OLS Specifications. Emitter Type: Laser. Available Wavelengths: 1310/1550 nm. Wavelength Tolerance: ±20/±20 nm. Spectral Width (FWHM): 5 nm (maximum). VFL Specifications. Wavelength: 650 nm ±20 nm. Output Power (nominal): 0.8 mW.



 

Standard Calibration $405.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the NOYES OFL250-100. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a contiguous set of frequencies within which a fiber optic component, link or network will operate.

Extinction Ratio (ER)
Extinction Ratio is the ratio of two optical power levels, of a digital signal generated by an optical source, (example a laser diode), where P1 is the optical power level generated when the light source is "on," and P0 is the power level generated when the light source is "off." The extinction ratio may be expressed as a fraction, in dB, or as a percentage.

Optical Signal-to-noise Ratio (OSNR)
Optical Signal-to-noise ratio is the ratio between the signal power and the noise power in a given bandwidth. Most commonly a reference bandwidth of 0.1 nm is used. This bandwidth is independent from the modulation format, the frequency and the receiver. For instance a OSNR of 20dB/0.1nm could be given, even the signal of 40 GBit DPSK would not fit in this bandwidth. OSNR is measured with a Optical Spectrum Analyzer. It is generally measured at the wavelength of interest.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Wavelength Repeatability
Wavelength Repeatability is the random uncertainty in reproducing a wavelength after detuning and re-setting the wavelength. The wavelength repeatability is ± half the span between the maximum and the minimum value of all actual values of these wavelengths. Example test condition: uninterrupted TLS output power, constant power level, temperature within operating temperature range, coherence control off, short time span. Note: NOTE The long-term wavelength repeatability can be obtained by taken the wavelength repeatability and wavelength stability into account.

Please contact us for your NOYES OFL250-100 CALIBRATION and/or NOYES OFL250-100 Handheld OTDR, OPM, LS and VFL REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: