NEWPORT 8605 CALIBRATION and NEWPORT 8605 REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the NEWPORT 8605 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Laser Diode Controller?
Shop for Comparable Products on our  used Laser Diode Controller page

 
   NEWPORT 8605   Description / Specification:    
NEWPORT 8605 500 mA Laser Diode Driver, 15 W TEC Combination Module

The Newport 8605 500 mA LDD, 2.5A/6V TEC Combination Module gives you full control of your laser diodes. The TEC section temperature stabilizes your laser diode. On the LDD section, an internal function generator provides sine and square wave modulation. Specifications. Laser Output Current Range: 0 to 500 mA. Current Resolution: 0.0076 mA. Output Current Accuracy: 0.03 + 15 µA. Compliance Voltage: 7 V. Temperature Coefficient (Full Scale): < 50 ppm/°C. Short-Term Stability (1 h) (ppm FS): < 10. Long-Term Stability (24 h) (ppm FS): < 50. Noise/Ripple (rms): < 2 µA. Current Limit Range: 0 to 500 mA. Resolution: 1 mA. Accuracy: ±2 mA. Internal Function Generator Waveforms: sinewave, squarewave. Frequency Range: 200 Hz to 300 kHz. Squarewave Duty Cycle: 50 ±5%. Independent Output Set Points: I max, I min. Frequency Jitter: <1%. Frequency Accuracy: ±5%. Amplitude Accuracy: ±5%. Sinewave THD: <2%. Squarewave Risetime: <1 µs. Photodiode Input Range: 0 to 5 mA. Monitor Current Stability (24 h): ±0.02% FS. Monitor Current Accuracy: ±(0.004% + 0.5 µA). Temperature Coefficient: <0.02% FS/°C. Measurement Display Output Current Range: 0 to 500.00 mA. Output Current Resolution: 0.01 mA. Output Current Accuracy: ±(0.02% + 20 µA). Forward Voltage Range: 0.000 to 7.000 V. Forward Voltage Resolution: 0.1 mV. Forward Voltage Accuracy: ±(0.005% + 1 mV). Photodiode Current Range: 5 to 5000 µA. Photodiode Current Resolution: 0.1 µA. Photodiode Current Accuracy: ±(0.01% + 0.5 µA). TEC Output Type: Bipolar, low noise. Maximum Current: 2.5 A. Compliance Voltage: >6 V. Typical Power: 15 W.



 

Standard Calibration $290.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the NEWPORT 8605. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bit Error Ratio (BER)
Bit Error Ratio (BER) is the ratio of errors caused by the number of bits in a data stream that have been altered due to noise, interference, distoriton or bit synchronization errors.

Flatness
Variation of insertion loss on the passband of an optical device.

Polarization Dependent Loss (PDL)
Polarization Dependent Loss is the difference between the maximum and minimum values of loss due to the variation of the polarization states of light propagating through a device. PDL is expressed in decibels. Calculated by; PDL = 10 log10 (Ep/Es), where EP and ES are the measured diffraction efficiencies for P- and S-plane polarized incident light, respectively.

Return Loss (RL)
Return Loss (RL) is the ratio of the incident power to the reflected power expressed in dB. RL = 10log (Pin/Pback)

Wavelength Resolution
Wavelength Resolution is the smallest possible displayed wavelength increment/decrement.

Please contact us for your NEWPORT 8605 CALIBRATION and/or NEWPORT 8605 500 mA Laser Diode Driver, 15 W TEC Combination Module REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: