Custom-Cal has for sale a new PROTEK A734. Also, short calibration turn times minimize downtime and reasonable rates decrease your long-term cost of ownership and minimizes downtime of the PROTEK A734. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another RF Spectrum Analyzer?
Shop for Comparable Products on our
 used RF Spectrum Analyzer page or new RF Spectrum Analyzer page

List Price for a new PROTEK A734, $4,500.00   PROTEK A734   Description / Specification:   Spec Sheet 
PROTEK A734 4.4 GHz Handheld Spectrum Analyzer

The Protek A734 handheld spectrum analyzer has been optimized for the convenience of mobility with lightweight (<2 Kg), 5.7 inch sunlight readable LCD, long battery life (> 8 hours) and smart battery indicator. Comparable DANL (Displayed Average Noise Level) enables users to detect more accurately low level of signals and additional features such as phase noise measurement, audio listen, and zero span options. Specifications. Frequency Range: 100 kHz to 4.4 GHz. Frequency Span Mode: Center Freq + Span or Start Freq + Stop Freq, ZERO Span. Frequency Span: ZERO SPAN, 600 Hz to 4.4 GHz. Frequency Minimum Span: 600 Hz. Internal Frequency Reference Accuracy: ±1 ppm. RBW: 0.1 Hz to 250 kHz & 5 MHz(0.1, 0.2, 0.4, 0.8, 1.6, 3.2, 6.5, 13, 25, 50, 100~). Amplitude Measurement Range: DANL ~ 1dB Gain Compression, 1dB Gain Compression (attenuator 15 dB, preamp off), +16 dBm Typical 1 Hz to 150 MHz, +19 dBm Typical 150 MHz to 4.4 GHz. Displayed Average Noise Level: 0 dB ATT, 1 Hz RBW. Amplitude Unit: dBm, dBmV, Watt, V. Maximum Safe Input Level (preamp off, 15 dB Att): +20 dBm. DC Volt: ±0.2 V max. Zero Span Sweep Time: 10 ms to 2 sec ( ±0.1%) All other sweep times are estimates reported after sweep completes. RF Connector: RF Signal IN, N type Female 50 Ohm. BNC External Time base: 10 MHz in, BNC type Female. Display Type: 5.7" Color TFT-LCD.


Standard Calibration $350.00 *
*This is a Web introductory price for one calibration of the PROTEK A734. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.

Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Available Gain
Available Gain is the ratio, at a specific frequency, of power available from the output to the power in from the source.

Frequency Span
Frequency Span specifies the range between the start and stop frequencies, also referred to as bandwidth

Peak Envelope Power
Peak envelope power is the maximum value of the envelope power. Envelope power is measured by making the averaging time much less than 1/fm where fm is the maximum frequency component of the modulation waveform. The averaging time is therefore limited on both ends: (1) it must be small compared to the period of the highest modulation frequency, and (2) it must be large enough to be many RF cycles long.

Please contact us for your new PROTEK A734 sale price and/or PROTEK A734 CALIBRATION

I'm interested in: 
Calibration Type (Select one):

Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:

What is the description of the problem?

How/when did the problem start?

 (*) Required Fields    For formal quote please fill in all fields.
From (Email):*
Contact Name:*
Address 1:
Address 2:
State/Territory/Province: *
Zip/Postal Code: