NOISE-COM UFX7111 CALIBRATION and NOISE-COM UFX7111 REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the NOISE-COM UFX7111 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

 

 
   NOISE-COM UFX7111   Description / Specification:    
NOISE-COM UFX7111 2 GHz Amplified Noise Source

The Noise Com UFX7111 is a 2 GHz amplified noise source that is tuned to provide the best flatness at the instrument output. The amplifier is optimized to deliver an output with a Gaussian amplitude distribution. Noise output power level can be adjusted from 0 to 127 dB in 1 dB (optionally 0.1 dB) steps.

Specifications.

Frequency Range: 1 GHz - 2 GHz.
Power: + 10 dBm.
dBm/Hz: -80.
Flatness: ±1.5 dBm.
μV/sqrt(Hz): 22.4.
Output: White Gaussian noise.
Attenuator: 0 to 127 dB in 1 dB steps, 0 to 79 dB above 2 GHz, (0.1 dB steps optional).
Control: Local and IEEE-488.
Impedance: 50 ohms (others optional).
Typical VSWR: 1.5:1.
Standard output connector: SMA female.

Options.
U7opt01: N female output connector.
U7opt02: BNC female output connector.
U7opt03: 0 to 127.9 dB noise attenuator in 0.1 dB steps instead of 127 dB in 1 dB steps.
U7opt04: Switch elements, 2 X SP6T for 4 subband filters, 1 thrupath, 1 termination (filters are optional).
U7opt06: 75 ohm output impedance (6 dB loss in the noise path and 12 dB loss in the signal path).
U7opt07: Combiner for input signal (6 dB loss in noise and signal paths).
U7opt08: Double output terminals (switched).
U7opt10: Line power 230 VAC, 50 Hz.
U7opt11: RS-232C, RS-422, RS-423, in addition to standard IEEE-488 interface.
U7opt12: 0 to 127 dB signal attenuator in 1 dB steps.
U7opt13: 0 to 127.9 dB signal attenuator in 0.1 dB steps.



 



Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Crest Factor
Crest factor or peak-to-average ratio (PAR) is a measurement of a waveform, calculated from the peak amplitude of the waveform divided by the RMS value of the waveform

Linearity
Linearity is the relative difference between the displayed power ratio, Dx/D0, and the actual (true) power ratio Px/P0 caused by changing the displayed power level from the reference level, D0, to an arbitrary displayed level, Dx.

Phase Noise
Phase noise is the frequency domain representation of rapid, short-term, random fluctuations in the phase of a waveform, caused by time domain instabilities. Phase noise (L(f)) is typically expressed in units of dBc/Hz, representing the noise power relative to the carrier contained in a 1 Hz bandwidth centered at a certain offsets from the carrier.

Sensitivity
Sensitivity is the minimum magnitude of input signal required to produce a specified output signal having a specified signal-to-noise ratio, or other specified criteria.


Please contact us for your NOISE-COM UFX7111 CALIBRATION and/or NOISE-COM UFX7111 2 GHz Amplified Noise Source REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: