A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ANRITSU MS2026B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Network Analyzer, SNA, VNA?
Shop for Comparable Products on our
 used Network Analyzer, SNA, VNA page or new Network Analyzer, SNA, VNA page

   ANRITSU MS2026B   Description / Specification:    
ANRITSU MS2026B 6 GHz VNA Master Handheld Vector Network Analyzer

The Anritsu MS2026B VNA Master is a handheld solution to address cable and antenna measurement needs in the field. The MS2026B VNA Master covers applications up to 6 GHz, which contains a wide variety of RF and microwave systems, both coax and waveguide. Equally impressive, this measurement tool offers the industry’s first 12-term error correction algorithm in a handheld VNA. With typical measurement speed of 750 μsec/point, the VNA Master is also ideally suited for transmission measurements anytime, anywhere.

Frequency Range: 5 kHz to 6 GHz.
Frequency Accuracy: 1.5 ppm.
Frequency Resolution: 1 kHz.
Typical Test Port Power:
  5 kHz to ≤ 3 GHz; +3 dBm (High Port) -25 dBm (Low Port),
  3 GHz to ≤ 6 GHz; +3 dBm (High Port) -25 dBm (Low Port).
Transmission Dynamic Range:
  5 kHz to ≤ 3 GHz 80dB,
  3 GHz to ≤ 6 GHz 75 dB.
Typical Sweep Speed: 525 μs/point.
Dynamic Range: 65 dB.
IF Bandwidth: 10, 30, 100, 300, 1k, 3k, 10k, 30k, 100k (Hz).
Data Points: 2 to 4001 (arbitrary setting); data points can be reduced without recalibration.
Maximum Input (Damage Level) into Vector Network Analyzer: +23 dBm, ±50 VDC.

MS2026B-0002 Time Domain (includes DTF capability).
MS2026B-0005 Power Monitor (requires external detector).
MS2026B-0007 Secure Data Operation.
MS2026B-0010 Built-in Bias-Tee.
MS2026B-0015 Vector Voltmeter.
MS2026B-0019 High Accuracy Power Meter (requires external USB sensor).
MS2026B-0031 GPS Receiver (requires GPS antenna, 2000-1528-R).
MS2026B-0077 Balanced/Differential S-Parameters, 1-port.


Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Average Power
Average power means that the energy transfer rate is to be averaged over many periods of the lowest frequency involved. For a CW signal, the lowest frequency and highest frequency are the same, so average power and power are the same. For an amplitude modulated wave, the power must be averaged over many periods of the modulation component of the signal as well.

A harmonic of a wave is a component frequency of the signal that is an integer multiple of the fundamental frequency, i.e. if the fundamental frequency is f, the harmonics have frequencies 2f, 3f, 4f, . . . etc.

Phase Noise
Phase noise is the frequency domain representation of rapid, short-term, random fluctuations in the phase of a waveform, caused by time domain instabilities. Phase noise (L(f)) is typically expressed in units of dBc/Hz, representing the noise power relative to the carrier contained in a 1 Hz bandwidth centered at a certain offsets from the carrier.

Please contact us for your ANRITSU MS2026B CALIBRATION and/or ANRITSU MS2026B 6 GHz VNA Master Handheld Vector Network Analyzer REPAIR

I'm interested in: 
Calibration Type (Select one):

Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:

What is the description of the problem?

How/when did the problem start?

 (*) Required Fields    For formal quote please fill in all fields.
From (Email):*
Contact Name:*
Address 1:
Address 2:
State/Territory/Province: *
Zip/Postal Code: