KEYSIGHT N5767A CALIBRATION and KEYSIGHT N5767A REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the KEYSIGHT N5767A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another DC Power Supply?
Shop for Comparable Products on our
 used DC Power Supply page

 
   KEYSIGHT N5767A   Description / Specification:    
KEYSIGHT N5767A 60V 25A Single-Output Switching Regulated DC Power Supply

The Keysight N5767A is a switching regulated, single-output programmable DC power supply. It provides stable output power, built-in voltage and current measurement. The N5767A provides up to 1500 W in a small space-saving 1U high, 19-inch wide package. Its air vents are in the front, side and rear (not on the top or bottom), so you can stack other instruments directly above or below it to save valuable rack space. It has a universal AC input so they can be automatically operated from any AC mains input worldwide. They can be operated from line voltages of 85 - 265 VAC, 47 to 63 Hz, with no switch to set or fuses to change when you switch from one voltage standard to another. They also provide power factor correction. To safeguard your device from damage, the N5767A power supply provides over-temperature, over-current and over-voltage protect (OVP) to shut down the power supply output when a fault occurs. They also offer an undervoltage limit (UVL) that prevents adjustment of the output voltage below a certain limit. The combination of UVL and OVP capabilities lets you create a protection window for sensitive load circuitry. Should you need greater output power, the Keysight N5767A power supply gives you the flexibility to connect in parallel up to four similarly rated units for greater output current and connect two similarly rated units in series for greater output voltage (see DC float voltage information).
Specifications.

Voltage: 60 V.
Current: 25 A.
Power: 1500 W.
Programming accuracy Voltage: 0.05%+ 30 mV.
Programming accuracy Current: 0.1%+ 25 mA.
Output ripple and noise CV p-p (Up to 20 MHz): 60 mV.
Output ripple and noise CV rms (From 5 Hz - 1 MHz): 8 mV.
Readback accuracy Voltage: 0.1%+ 60 mV.
Readback accuracy Current: 0.1%+ 75 mA.
Load regulation (change from 10% to 90%):
Voltage 8 mV / Current 75 mA.
Transient response time: <= 1 ms.
DC floating voltage: No output terminal may be more than ±60 VDC from any other terminal or chassis ground.
I/O interface: GPIB, LAN, USB standard.



 

Standard Calibration $95.00 *
*This is a Web introductory price for one calibration of the KEYSIGHT N5767A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBm
dBm (sometimes dBmW) is an abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). Zero dBm equals one milliwatt. A 3 dB increase represents roughly doubling the power, a 3 dB decrease, the power is reduced by about one half.

Millimeter-wave
Millimeter-wave is a term that generally refers to frequencies of 26.5 GHz and above. That is where signal wavelengths fall below approximately 10 mm, and thus the terminology changes from centimeters to millimeters.

Power Repeatability
Power Repeatability is the random uncertainty in reproducing the power level after changing and re-setting the power level. The power repeatability is ± half the span (in dB) between the highest and lowest actual power. Note: - The long-term power repeatability can be obtained by taken the power repeatability and power stability into account.

Stability
Stability is the extent to which a specified property, characteristic, or parameter of a substance, device, or apparatus, remains fixed with the passage of time or with varying environmental conditions.


Please contact us for your KEYSIGHT N5767A CALIBRATION and/or KEYSIGHT N5767A 60V 25A Single-Output Switching Regulated DC Power Supply REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: