A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the KEYSIGHT N5762A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another DC Power Supply?
Shop for Comparable Products on our
 used DC Power Supply page

   KEYSIGHT N5762A   Description / Specification:    
KEYSIGHT N5762A 8V 165A Single-Output Switching Regulated DC Power Supply

The Keysight N5762A is a switching regulated, single-output programmable DC power supply. It provides stable output power, built-in voltage and current measurement. The N5762A provides up to 1320 W in a small space-saving 1U high, 19-inch wide package. Its air vents are in the front, side and rear (not on the top or bottom), so you can stack other instruments directly above or below it to save valuable rack space. It has a universal AC input so they can be automatically operated from any AC mains input worldwide. They can be operated from line voltages of 85 - 265 VAC, 47 to 63 Hz, with no switch to set or fuses to change when you switch from one voltage standard to another. They also provide power factor correction. To safeguard your device from damage, the Keysight N5762A power supply provides over-temperature, over-current and over-voltage protect (OVP) to shut down the power supply output when a fault occurs. They also offer an undervoltage limit (UVL) that prevents adjustment of the output voltage below a certain limit. The combination of UVL and OVP capabilities lets you create a protection window for sensitive load circuitry. Should you need greater output power, the Keysight N5762A power supply gives you the flexibility to connect in parallel up to four similarly rated units for greater output current and connect two similarly rated units in series for greater output voltage (see DC float voltage information).

Voltage: 8 V.
Current: 165 A.
Power: 1320 W.
Output ripple and noise CV p-p (Up to 20 MHz): 60 mV.
Output ripple and noise CV rms (From 5 Hz - 1 MHz): 8 mV.
Load regulation (change from 10% to 90%): Voltage 2.8 mV / Current 38 mA.
Programming accuracy Voltage: 0.05%+ 4 mV.
Programming accuracy Current: 0.1%+ 165 mA.
Measurement Readback accuracy Voltage: 0.1%+ 8 mV.
Measurement Readback accuracy Current: 0.1%+ 495 mA.
Transient response time: ≤1.5ms.
DC floating voltage: No output terminal may be more than ±60 VDC from any other terminal or chassis ground.
I/O interface: GPIB, LAN, USB standard.


Standard Calibration $95.00 *
*This is a Web introductory price for one calibration of the KEYSIGHT N5762A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.

Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Carrier Wave (CW)
Carrier Wave or Continuous Wave is a sinusoidal signal without modulation.

A harmonic of a wave is a component frequency of the signal that is an integer multiple of the fundamental frequency, i.e. if the fundamental frequency is f, the harmonics have frequencies 2f, 3f, 4f, . . . etc.

Noise Floor
Noise floor is the measure of the signal created from the sum of all the noise sources and unwanted signals within a measurement system.

Ripple is the small unwanted residual periodic variation of the direct current (dc) output

Please contact us for your KEYSIGHT N5762A CALIBRATION and/or KEYSIGHT N5762A 8V 165A Single-Output Switching Regulated DC Power Supply REPAIR

I'm interested in: 
Calibration Type (Select one):

Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:

What is the description of the problem?

How/when did the problem start?

 (*) Required Fields    For formal quote please fill in all fields.
From (Email):*
Contact Name:*
Address 1:
Address 2:
State/Territory/Province: *
Zip/Postal Code: