Keysight (Agilent) 60504B REPAIR and Keysight (Agilent) 60504B CALIBRATION
 
Custom-Cal has a high success rate in the repair of the Keysight (Agilent) 60504B. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the Keysight (Agilent) 60504B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Electronic Load?
Shop for Comparable Products on our  used Electronic Load page

 
   Keysight (Agilent) 60504B   Description / Specification:    
Keysight (Agilent) 60504B 120 A, 600 W DC Electronic Load Module

The HP 60504B dc electronic load is optimized to address a broad range of dynamic loading applications. They are specifically designed for stability in applications where fast transients are applied to the load inputs, such as during dc power supply startup characterization or transient response testing. Dynamic load performance can be further tailored to specific application needs with the programmable slew rate feature. The HP 60504B meets all specifications when operated above 3.0 V; however, the dc operating characteristics also extend below this minimum-input voltage for static tests. Because of the FET technology used in the power input circuits, HP electronic loads have a low minimum-input resistance allowing them to sink high currents even at low voltages. Specifications. Amperes: 0 to 120 A. Volts: 3 to 60 V. Maximum power (at 40° C): 600 W. Constant current mode Ranges: 0 to 12 A, 0 to 120 A. Constant current mode Accuracy: 0.12% ±130 mA. Constant current mode Regulation: 10 mA. Constant voltage mode Accuracy 0.1% ±50 mV. Constant voltage mode Regulation (w/remote sense): 20 mV. Constant resistance mode Ranges: 0.017 to 0.5 ohm, 0.5 to 500 ohms, 5 to 5,000 ohms. Transient generator Frequency range: 0.25 Hz to 10 kHz (3% Accuracy). Current readback accuracy: 0.1% ±110 mA. Power readback accuracy: 0.2% ±8 W. Ripple and noise (20-Hz to 10-MHz noise): 6 mA rms, 60 mA peak-to-peak (Current), 8 mV rms (Voltage).



 

Standard Calibration $285.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the Keysight (Agilent) 60504B. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Average Power
Average power means that the energy transfer rate is to be averaged over many periods of the lowest frequency involved. For a CW signal, the lowest frequency and highest frequency are the same, so average power and power are the same. For an amplitude modulated wave, the power must be averaged over many periods of the modulation component of the signal as well.

Dynamic range
Dynamic range the ratio of a specified maximum level of a parameter, such as power, current, voltage or frequency, to the minimum detectable value of that parameter.

Modulation
Modulation is the process by which the characteristic of one wave (the carrier) is modified by another.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Please contact us for your Keysight (Agilent) 60504B REPAIR and/or Keysight (Agilent) 60504B 120 A, 600 W DC Electronic Load Module CALIBRATION
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: