Keysight (Agilent) 8720A REPAIR and Keysight (Agilent) 8720A CALIBRATION

Custom-Cal has a high success rate in the repair of the Keysight (Agilent) 8720A. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the Keysight (Agilent) 8720A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Network Analyzer, SNA, VNA?
Shop for Comparable Products on our
 used Network Analyzer, SNA, VNA page or new Network Analyzer, SNA, VNA page

   Keysight (Agilent) 8720A   Description / Specification:    
Keysight (Agilent) 8720A 20 GHz Microwave Network Analyzer

The HP 8720A 20 GHz Microwave Network Analyzer provides simple and complete vector network measurements in a compact and fully integrated microwave network analyzer. Characterize your microwave components and networks accurately. Integration of the 130 MHz to 20 GHz swept synthesized source, test set, and receiver results in a compact, low cost network analyzer which is ideal for incoming inspection, production, and final test measurements. With two independent display channels available, you can simultaneously measure the reflection and transmissions characteristics of the device under test. The easy-to-use softkey selection of measurement functions a llows you to quickly measure the magnitude, phase, or group delay characteristics of your device under test. Directly measure the electrical length of a single device or phase match multiple devices. Data can be displayed in log magnitude, linear magnitude, SWR, phase, group delay, polar, real, or Smith Chart formats. Source Frequency Characteristics; Range: 130 MHz to 20.0 GHz. Resolution: 100 kHz (1 Hz with Option 001). Stability: typically ± 7.5 ppm @ 0° to 55°C, typically ±3 ppm/ year. Accuracy: 10 ppm @ 25°±3°C. Output characteristics (at test ports, 25° ±3°C); Power range: -10 to -65 dBm in 5 dB steps. Power level: -10 dBm ± 3 dB. Harmonics: <-15 dBc @ -10 dBm (typical). Test ports; Connector type: 3.5 mm (male). Impedance: 50 ohms nominal. Switch type: Mechanical. Switch lifetime: >3 million cycles (typical). Maximum input level: + 20 dBm. DC bias: 500 mA , 40 VDC maximum. Options. Option 001, 1Hz frequency resolution. Option 010, Time Domain Capability.


Standard Calibration $400.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the Keysight (Agilent) 8720A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.

Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Noise Density
Noise Density is the amount of noise within a defined bandwidth, usually normalized to 1 Hz.

Spurious Signals
Spurious signals are undesired signals. They can be considered in two classes. They can be stationary; their frequency and amplitude do not change significantly, or non-stationary, where the frequency and/or amplitude change significantly over short time periods.

Please contact us for your Keysight (Agilent) 8720A REPAIR and/or Keysight (Agilent) 8720A 20 GHz Microwave Network Analyzer CALIBRATION

I'm interested in: 
Calibration Type (Select one):

Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:

What is the description of the problem?

How/when did the problem start?

 (*) Required Fields    For formal quote please fill in all fields.
From (Email):*
Contact Name:*
Address 1:
Address 2:
State/Territory/Province: *
Zip/Postal Code: