ANDO AQ-6315B REPAIR and ANDO AQ-6315B CALIBRATION

 
Custom-Cal has a high success rate in the repair of the ANDO AQ-6315B. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ANDO AQ-6315B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Optical Spectrum Analyzer, OSA?
Shop for Comparable Products on our
 used Optical Spectrum Analyzer, OSA page or new Optical Spectrum Analyzer, OSA page

As an alternative New Ridge Technologies offers the NRT-8000, the world’s Smallest Optical Spectrum Analyzer with built in “live wavelength calibration” for C-Band applications.  More
   ANDO AQ-6315B (AQ6315B)   Description / Specification:   Spec Sheet 
ANDO AQ-6315B 350 to 1750 nm Optical Spectrum Analyzer

The Ando AQ-6315B optical spectrum analyzer brings advanced capabilities to a wide range of applications, from light source evaluation to measurement of loss wavelength characteristics in optical devices. Features. The monochromator mode can be set to single-pass or double-pass to match your measurement application needs. Provides a dynamic range (stray light level) of 70dB or more ± 1 nm from the peak. This is especially valuable when measuring DFB-LD side-mode suppression ratio. Covers from 350nm to 1750nm and noise level has been suppressed to allows the AQ-6315B to measure light at down to -90dBm. Polarization dependency has been slashed to ± 0.05dB, enabling accurate measurement of optical amplifier gain and other critical measurements. Optical output is provided, can be used as an optical bandpass filter. 9.4-inch color LCD. Specifications. Measurement wavelength range: 350 to 1750 nm. Wavelength span: 0 to 1500 nm. Wavelength accuracy: ±0.5nm (25 ±5°C, 10/125 SM fiber). Wavelength reproducibility: ± 0.005nm (1 minute). Wavelength resolution: 0.05 to 10 nm. Level accuracy: ± 0.3dB (at 633/1310/1550nm). Interface GP-IB.



 

Standard Calibration $455.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANDO AQ-6315B. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a contiguous set of frequencies within which a fiber optic component, link or network will operate.

Extinction Ratio (ER)
Extinction Ratio is the ratio of two optical power levels, of a digital signal generated by an optical source, (example a laser diode), where P1 is the optical power level generated when the light source is "on," and P0 is the power level generated when the light source is "off." The extinction ratio may be expressed as a fraction, in dB, or as a percentage.

Optical Signal-to-noise Ratio (OSNR)
Optical Signal-to-noise ratio is the ratio between the signal power and the noise power in a given bandwidth. Most commonly a reference bandwidth of 0.1 nm is used. This bandwidth is independent from the modulation format, the frequency and the receiver. For instance a OSNR of 20dB/0.1nm could be given, even the signal of 40 GBit DPSK would not fit in this bandwidth. OSNR is measured with a Optical Spectrum Analyzer. It is generally measured at the wavelength of interest.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Wavelength Repeatability
Wavelength Repeatability is the random uncertainty in reproducing a wavelength after detuning and re-setting the wavelength. The wavelength repeatability is ± half the span between the maximum and the minimum value of all actual values of these wavelengths. Example test condition: uninterrupted TLS output power, constant power level, temperature within operating temperature range, coherence control off, short time span. Note: NOTE The long-term wavelength repeatability can be obtained by taken the wavelength repeatability and wavelength stability into account.


Please contact us for your ANDO AQ-6315B REPAIR and/or ANDO AQ-6315B 350 to 1750 nm Optical Spectrum Analyzer CALIBRATION

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: