ANRITSU 56100A REPAIR and ANRITSU 56100A CALIBRATION

 
Custom-Cal has a high success rate in the repair of the ANRITSU 56100A. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ANRITSU 56100A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Network Analyzer, SNA, VNA?
Shop for Comparable Products on our
 used Network Analyzer, SNA, VNA page or new Network Analyzer, SNA, VNA page

 
   ANRITSU 56100A   Description / Specification:    
ANRITSU 56100A Scalar Network Analyzer

Anritsu 56100A 10 MHz to 50 GHz, Scalar Network Analyzer. Measurements; Function: The 56100A has four detector inputs and two independent channels for measurement and display of detected RF power from Anritsu 560 Series Detectors and SWR Autotesters. Two independent channels display RF power (dBm), Transmission Gain or Loss in (dB), or reflected power. Voltage may be displayed with optional Volt Mode Adapter Cable. Frequency Range: 10 MHz to over 50 GHz in coax using Anritsu 560 Series Detectors and SWR Autotesters. Waveguide measurement components to 110 GHz support transmission, reflection, and power measurements. Inputs: Four inputs, A, B, R1, and R2 accept detected outputs from Anritsu 560 Series Detectors and SWR Autotesters. Dynamic Range: 76 dB (-60 dBm to +16 dBm) on all channels, useable to -65 dBm. Display; Channels: Two channels are used to select and simultaneously display any two inputs from A, B, R1, or R2. The same inputs can be displayed as ratios of A/R1, A/R2, B/R1, or B/R2. Display Resolution: Horizontal: 101, 201, or 401 points over selected frequency range, Vertical: 0.005 dB. Scaling Resolution: 0.1 dB to 10 dB per division in 0.1 dB steps with independent control for each channel. Scaling Offset Range: -99 dB to +99 dB in 0.1 dB steps. Averaging: 4, 8, 16, 32, 64, 128, or 256 successive traces can be averaged to smooth the trace display. Interface: IEEE-488 interface is standard.



 

Standard Calibration $725.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ANRITSU 56100A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc
dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Noise Density
Noise Density is the amount of noise within a defined bandwidth, usually normalized to 1 Hz.

Spurious Signals
Spurious signals are undesired signals. They can be considered in two classes. They can be stationary; their frequency and amplitude do not change significantly, or non-stationary, where the frequency and/or amplitude change significantly over short time periods.


Please contact us for your ANRITSU 56100A REPAIR and/or ANRITSU 56100A Scalar Network Analyzer CALIBRATION

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: